Corner Fireplace Insert Prity A – 14.2 kW

Built for the Corner. Sized for a Real Room.

Every home has corners that go unused — dead space that a rectangular insert can't take advantage of. The Prity A is shaped specifically for them, fitting neatly where two walls meet and radiating heat outward across the room from a position that maximizes reach rather than wasting it in a bare corner.

With 14.2 kW of radiant heat, a wide 800 mm firebox, and class A+ energy efficiency, the Prity A is a serious heating appliance dressed for a spot most inserts can't fill.

Made in Bulgaria. EU Ecodesign compliant.

How Much Space Can It Heat?

Prity doesn't publish an official heated-area figure for the Prity A, so this is our own estimate, based on the heated-area-to-power ratio observed across comparable Prity models in our range (roughly 7.5 m² per kW). At 14.2 kW, that puts the Prity A at approximately 105 m², depending on insulation, ceiling height, and room layout.

Corner Placement That Changes How a Room Heats

Positioning an insert in a corner isn't just a space-saving trick — it's a genuine heating strategy. A corner-mounted firebox radiates heat across a wide arc of the room rather than throwing it in a single direction from a flat wall, which means more even heat distribution, fewer cold spots, and a room that feels comfortable from more angles.

The Prity A's wide body is built to take full advantage of this position. At 1010 mm wide, it fills the corner with confidence, and its 800 mm firebox — one of the widest in our range — keeps the fire visible and the flames generously sized from across the room.

A Wide, Deep Firebox

The combustion chamber measures 800 mm wide, 515 mm deep, and 415 mm high — dimensioned for longer logs, bigger loads, and burns that hold their heat for longer stretches without constant attention.

Clean Combustion, A+ Efficiency

The Prity A achieves a combustion efficiency (η) of 81.1% and a seasonal space heating energy efficiency of 72%, with an energy efficiency index of 109 — placing it firmly in energy class A+. Emissions at nominal output are controlled across the board: CO at 1068 mg/Nm³, particulate matter at just 29 mg/Nm³, NOx at 90 mg/Nm³, and OGC at 28 mg/Nm³ — all within EU Ecodesign limits.

Fuel consumption at nominal output is 4.3 kg of dry wood per hour, with a flue gas temperature of 190°C and a mass flow rate of 12.6 g/s.

Important Installation Note

The Prity A uses a Ø200 mm flue outlet and requires a minimum chimney draught of 12.6 Pa. Please confirm your chimney connection is compatible with this diameter before ordering. Its corner geometry means installation requires careful planning of the surrounding hearth structure on both adjoining walls — professional installation is strongly recommended. At 110 kg, the unit also needs a floor and framing capable of supporting the weight.

Overall dimensions: 1010 × 650 × 730 mm (W × D × H).

30 Years of European Engineering Behind Every Weld

Prity has manufactured solid fuel heating appliances in Gorna Oryahovitsa, Bulgaria, since 1995. With more than 250 production staff and a range refined across three decades, the company builds inserts that earn their place in a home for years. Every unit is manufactured to the relevant EN standards and independently verified.

Your Prity A comes with a 24-month manufacturer's warranty.

Everything You Get

• 14.2 kW of radiant heat — suitable for spaces up to approximately 105 m², depending on insulation, ceiling height, and room layout

• Corner-mounted design — fits neatly into any room corner, radiating heat across the whole space

• Wide 800 × 515 × 415 mm firebox — among the largest in the Prity range

• Class A+ energy efficiency with a seasonal space heating energy efficiency of 72%

• Combustion efficiency (η) of 81.1%

• Fuel consumption: 4.3 kg of dry wood per hour at nominal output

• Overall footprint: 1010 × 650 mm

• Flue outlet: Ø200 mm — confirm chimney compatibility before ordering

• Net weight: 110 kg

• 24-month manufacturer's warranty

Box Contents

Insert body with heat-resistant glazed door, technical manual.

Use only dry, chemically untreated natural wood with a moisture content not exceeding 20%. Do not burn household waste, painted wood, plywood, or treated wood. Always consult a qualified installer before connecting the appliance to your chimney system, and before building the surrounding hearth structure for a corner installation. Note: this model requires a Ø200 mm connection.